QASHQAI-ELEC.COM
Language :  FR  EN  |  Contact-us    


Kit for automatic power folding mirrors : Key

Image

Description : This kit for Nissan Qashqai can add a function to open and close automatically power folding mirrors on opening/closing door with key or the 3 exterior buttons on car.

Car : Nissan Qashqai.
Check prerequisites

Warranty : 1 year

 
79 €
69 €
Buy

Payment method
Buy

Availability
IN STOCK


Features video




Fonctionnement


fonct 01 1 - Open Position
In this position power folding mirror will always stay close (Automatic mode disable).

2 - Automatic Position
In this position power folding mirror will be opened when opening door and closed when closing door.

fonct 01 fonct 01
fonct 01 fonct 01

3 - Close Position
In this position power folding mirror will always stay open (Automatic mode disable).


Product Details

System
Kit contents Electronic box
6 connectors and cables
Installation guide
Power supply 12 V on the vehicle
Protection 2A Fuse with Fuse Holder
Operating temperature -40° C +85° C
Electronic unit dimensions 50 x 50 x 20 mm

Fonctions
Automatically power folding mirros on opening/closing door with radio key Yes (Works with or without Nissan Intelligent Key)
Automatically power folding mirros on opening/closing door with the 3 buttons located on the exterior doors of car Yes
Keep the manual switch functions available Yes
Power folding mirrors can be used engine stopped Yes
Anti-Carjacking Compatibility : Automatic doors lock above 15 km/h (10 miles) Yes (The mirrors will not close automatically while driving)
Anti-Carjacking Compatibility : Selective unlocking of driver's door Yes, however 2 beeps are necessary to open automatically mirrors.
(Note this anti-carjacking system can be disable on vehicle)

Compatibility
Nissan Qashqai, Qashqai + 2 (2007 - 2013) Fully Compatible
Version Acenta, Optima, N-Tec, Connect Edition, Tekna, Bose, 360.

(Visia version doesn't have power folding mirrors)

Installation
Wire cutting need No
Soldering need No
Installation type By connectors


Installation

No wire cutting, no soldering, Qashqai-Elec products are made with Nissan connectors. You only need dismantling plastic coverings. You can complete the installation by yourself or by our nissan dealer.

Level Required : Practised



1. Turn off your car before starting the installation.  
2. Disassemble the plastic of the running threshold on driver's side. Disengage the 3 clips along it.    
3. Disassemble the plastic near the foot rest. Unscrew the plastic nut at the top. Then disengage the clips.    
4. At the rear door on driver's side. Retract the bellows inside the pillar.    
5. Disengage the plastic in the bottom of the pillar on driver's side. Start with disengage the two clips in the upper part.    
6. Toggle the bottom of the pillar to access wire.    
7. Rotate the white plastic holding the cable inside the pillar. Disengage the top clip with pliers.
8. Disconnect the existing cable in the center pillar.
9. Set up the kit by clipping both male and female connectors on the existing connectors. Then enter the whole inside of the pillar.  
10. Make cable running from center pillar to the footrest.  
11. Replace the white cover; put the clamps to properly bind the cables.  
12. Collapse all plastics.
13.

Open the mirrors's control switch panel on the left of the steering wheel. Slide the spatula under the control panel then do a forward pressure to lift the panel.

14. At the back of the control panel: Remove the connector from the top by performing a pressure then rotated with a screwdriver in the slot provided for this purpose.
15. Set up the kit by clipping both male and female connectors on the existing connectors.
16. Attach the electronic box with the collar on the existing cable. The electronic box must be positioned to the left of the cable.  
17. Open the fuse panel.
18. Pass the red wire behind the control switch panel (down) towards the fuse box.
19. Run the 2 pin female connector from the foot rest to the fuse box.  
20. On the kit connect the 2 pin male connector with 2 pin female (With cable supplied in the kit).
21.

Place the fuse holder on the slot number 10 on the fuse center line.

Warning ! The fuse holder must be oriented wire down.

If the fuse slot is already in use, remove the fuse in slot number 10 on the center line and insert the fuse on the kit in Fuse Ext slot. Then plug the fuse holder on fuse slot number 10.

Warning ! Do not use the kit with an existing fuse over 20 A.

22. Close the control panel by making a push.  
23. Close the fuse panel.  

Remove plastic coverings. Lastly you need to connect the system to the existing Nissan connectors.
No wire cutting, no welding.


PayPal PayPal Paiement Fedex Colissimo Colissimo